Archive for March, 2009

Scratchbuilding How-To’s Up!

March 25th, 2009 No comments

I’ve taken my ginormous “Pretty Much Everything I Know About Scratchbuilding Article” and made a PDF out of it. I posted it in the “Tips And Advice And Things” Category. Dig in!

Mustang from hell…

March 25th, 2009 No comments

I went back to work on the Mustang, but then had some… problems… with the canopy.

Here’s Swanny’s review of the Tamiya kit:

Swanny’s review

If you look at the parts runner picture, you see a little runner on the left with a pilot and the frame of the canopy. The frame has a cross brace and a place near the back where teh inner curve of the frame becomes flat. To this frame, the clear bubble of glass is glued.

Hasegawa has molded the entire canopy as one thin clear piece. This requires a much more difficult bit of masking becasue getting that line straight around a the compound curve of the canopy ain’t easy, especially with the pitiful suggestion of a demarcation they have molded into it. On top of that, you have to glue two pieces of detail into the canopy (the cross brace and a little flat piece of plastic that makes the flat part of the inner curve). This, IMO, looks terrible and is tricky with the little barely-there markers they give you to glue the pieces to. Then, once you place the canopy on the fuselage, you see that it’s too wide by a good 32nd of an inch. All these gluing steps wouldn’t be too hard to handle, but I always try to glue my airplane canopies with white glue because it dries clear and won’t cause the clouding or fingerprints you sometimes get with CA super glues.

The problem is that the white glue isn’t strong enough to hold the canopy on once it’s squeezed into place. And in all the time I spent squeezing and holding the canopy trying to glue it in place, the two parts I glued inside of it were coming loose, and the cross-brace was wanting to lean to the back.

I finally gave up on the white glue and very carefully put tiny bits of CA glue on it and glued it. There were still cracks between the canopy and the fuselage, but I decided I could just live with it…

But anyway, I finally get the canopy on and the cross brace is leaning back, but like I said, I can live with it. I mix up some cockpit interior color and spray it (so that when you look inside, the inside of the canopy frame will be the appropriate cockpit color). Then I mix up some primer.

I go to dust the model off and it slips off its skewer and falls a couple feet onto the carpet and the rudder breaks off as well as the f–king canopy and I pick up the canopy and realize the two pieces glued inside popped off as well. Thus most of my progress of the last two nights is gone.

At that point I used every bit of profanity in my arsenal to curse this POS kit. I scoured the floor and found those two little bits then I put the model down gave my AB a once-over cleaning and walked away.

Well, I didn’t really think I would finish, but jeez I thought I would get farther in 31 days. On paper this was going to be a really simple project.

There’s not a lot of progress to show for the last week. Four rounds of puttying, priming, and panel line re-scribing later and it still needs a little more work. Of course this will all show in the end when I have a nice, smooth model.

There were several spots on the Mustang where the parts fit was pretty bad and needed to be sanded deep enough that panel re-scribing was necessary, including the air scoop under the chin, the scoop under the wings, all the landing gear doors, the horizontal stabilizers, and, by far worst of all the canopy.

I finally got the damn thing glued on (with Tamiya liquid cement, gtetra’s good idea), and the fit is TERRIBLE! I mentioned before that the canopy was too wide where the front of the canopy met the fuselage, but once I got it on, I saw that it was also crooked, the base was not flat, leaving a gap on the sides between the canopy and fuselage, and too narrow in the back, leaving the canopy on a shelf:

Soooo… A good gob of Tamiya putty, a couple coats of Mr. Surfacer 500 and lots of sanding later…

And It’s still not quite done sanding, although I believe I’m on the final round. I’ve painted Mr. Surfacer 500 on to touch up a few more places and after I sand that smooth I’ll have to restore more surface detail. The experience I got in panel lining the Sazabi is really paying off in this model. The part that’s really gonna suck is going to be recreating the break between the canopy and fuselage, since the putty has blended them together seamlessly.

Then it’s primer, gloss black lacquer and Alclad. I think painting should go very quickly, depending on how much I shade the Natural Metal Finish and try picking out different panels to make slightly different shades of Aluminum.

Anyway, here I am on Day 31…

Hall of shame all the way, but I think I’ll get a nice model once it’s all done and I’ll have made a naturalistic dio, which will be one more major skill under my belt.

Funakatown Has Arrived!

March 20th, 2009 No comments

Well, it took a couple of months, but the basic Funakatown website is complete! The Complete Models Launchpad and Models In-Progress Launchpad are both complete as are all the galleries and WIPs associated with them.

I’ll next add a page category like “Tips” or “Articles” or “How-To’s” where I’ll put my “Everything I know about Scratchbuilding” and spraybooth how-to articles, but for now the website is ready to roll out.

Categories: Generic Ramblings Tags:

Mustang Internals and a Tuskegee Airman

March 20th, 2009 No comments

It’s been an off week for building. My wife has had a hectic work schedule which meant more time with my daughter which means less time to build. I’ve been putting some time into the project, but it just doesn’t seem like I’m getting anywhere. I had hoped to prime the model by this weekend, but it just hasn’t happened.

Here’s what I have done…

Both the interior of the Mustang and the pilot got a sludge wash of oil paint thinned with odorless paint thinner.

I then clearcoated the parts and gave them a drybrushing with oil paints to bring out highlights and assembled all the parts that make up the interior of the cockpit and underbelly intake/exhaust system.

After a few days I decided my pilots face, which I had worried about being too dark before the drybrushing was now too light, so I mixed up another shade of brown and re-drybrushed it:

Now it seems a bit too orange, but I gotta stop somewhere or the paint is gonna get too thick.

Having glued the fuselage together around the cockpit, I now turned my attention to cleaning up the control surfaces which I had cut out earlier, and filling in the gaps where I had cut off the rudder and ailerons:

And since I’ve always got time to complain, here’s a shot of some of the not-so-great parts fit I’m dealing with. I know I’ve been spoiled by the Bandai and Tamiya kits I’ve been building, but still, I don’t need this kind of stuff on a speed build:

Here’s the Mustang all glued together. I’ve since applied putty to the seams, but have yet to sand it off. In a few placed the parts fit is far enough off that I’ll have to sand bits of the surface off and re-scribe surface detail. Yay.

I’ve also been doing a bit of work on the Citroen and its inhabitants. The vignette calls for the Germans to be getting out of a car that they would probably assume is about to be strafed. The problem is that the German figures that come with the car are just casually standing around.

I decided for the Luftwaffe officer in back that this would be OK. Call it nerves of steel or fatalism or say his piloting experience made him realize that the Mustang’s angle of attack was wrong for a strafing run. Maybe he’s just too amazed by the Mustang’s Black pilot. Here’s the pilot. I changed the position of his left arm so it would rest on the Citroen’s door and used Magic Sculpt to fill in the gaps:

The driver is tougher. I had originally imagined him cowering under a tree or running away in a crouch. The problem is that non of the figures is in a posture anywhere near that. But, I found that by taking one figure and putting different arms on him, and changing the angles of the arms, I get a pretty decent figure of a guy who just jumped out of the car and is trying not to let the door hit his ass on the way out:

The feet look kind of static, I may reposition one of them to look like he is about to break into a run. Both figures have their heads stuck on with sticky tack since I won’t glue them until I work out the positioning of the figures and make sure they are looking in the right direction.

Categories: Models In-Progress Tags:

Galleries Up!

March 12th, 2009 No comments

Okay, seriously this time. These galleries are built using WordPress, so even if I make changes to my theme, they’ll still be there. I’ve also put up my first WIP page and got those links working. If I get the WIPs done, then I’ll have a working website and then I can work on fine-tuning it and getting some better widgets, etc… I can even tell people about it and not be embarrassed. Woot!

And just because it’s been in my head, here’s my lyric of the day:

“I’m so into you
But I’m way too smart for you
Even my henchmen think I’m crazy
I’m not surprised that you agree
If you could find some way to be
A little bit less afraid of me
You’d see the voices that control me from inside my head
Say I shouldn’t kill you yet ”

Check it out:

Skullcrusher Mountain by Jonathan Coulton

Categories: Generic Ramblings Tags:

Growing Pains (and Modding Pains)

March 6th, 2009 No comments

Still slowly fixing the gallery pages. I keep thinking up improvements as I go, so I have to go back and add the changes back to the finished pages…

The good thing is that I’ve figured out page nesting so now I’m just putting the pages out through WordPress, which is way easier, I just have to live with really short titles, or my pull-down menus look like crap.

Anyway, let’s look at my current project, shall we?

Unfortunately I’ve found this Hasegawa Mustang has nothing on Tamiya… Maybe it’s because it’s just a little older than the other two Tamiya airplane kits I’ve built. The Tamiya kits could be test fitted and the major components would stay together more or less without glue because the parts fit is so good.

This Hasegawa Mustang is made of thin flexible plastic so that the wing and fuselage halves are warped. It’s nothing glue doesn’t solve, but not as good as Tamiya.


All Mustang parts are de-sprued (all 20 of them). I’ve also finished one of the hard parts, cutting off all the control surfaces that will need to be deflected in a high angle knife-edge pass. I used a needle in a pinvise and a zillion repetitions of scoring to remove them with minimal damage to the parts.

The next challenge was the landing gear doors…

Since the plane will be flying, the landing gear doors have to be closed. Do the Hasegawa kit’s landing gear doors fit in the wheel wells like they should?

Of course not.

Are they even close?

Not really.

The gear door on the right has been significantly shaved down on the inside to fit better. The one on the left is OOB.

I thought building the kit in flight would be really easy since I wouldn’t have to paint and detail the landing gear and the cockpit could be simple since the pilot would be obstructing most of it. After fixing the landing gear, I’m convinced that this is actually more work…

Here’s what I had to do to the inside to get the landing gear doors in the wheel wells. Top is OOB, bottom is filed down:

I decided that the wheel wells would be the best place to insert a polycap where I could mount the Mustang on a stand, so I scraped a flat spot in the surface detail inside and stuck this Wave socket in place:

I painted it red so I could place the door over it and mark where I needed to drill a hole:

After drilling the hole, I glued the gear doors on. I had to use a bit of white plastic to fix where I had ground too much off. You can’t see it in this pic, but the gear doors still stick out above the surface of the rest of the wing. You can see it better on the door on the right side in the first picture.

After sanding it all down flush, I had a kinda OK looking set of retracted landing gear. I’ll still fill in the cracks with Mr. Surfacer 500 and re-scribe the lines to clean it all up.

You know what really sucks? I have a Tamiya kit of the same airplane in the same scale. Just to torture myself, I decided to check if the landing gear doors fit in the wheel wells.

They do. Perfectly.

Freakin’ Hasegawa. Unfortunately I had already desprued all the parts of the Tamiya kit, so it wasn’t eligible for the 31 Days competition. Besides, I want to use the better Tamiya kit later on for a full-open model of the Mustang. I’ve already got a set of photo etched metal parts for it.

Next up was the cockpit. This where I kind of catch a break. Like I said before, having the pilot sitting there means that the detail can be kinda soft in the cockpit since the pilot will block most of it off.

I had this pilot figure from the Tamiya kit. I came molded in 4 pieces, body, left arm, right arm and head. I still had to hack it up a bit, though. I had to file down the neck so I could tilt the head up:

Then I had to go to work on the left arm, which is meant to hang out the open cockpit. Since the cockpit will be closed, that wouldn’t work. I had to cut it at the elbow to change the angle of the hand to make it look like it was resting on the throttle. I then had to glue the arm to the side of the body and leave a huge gap where the shoulder should have been. I then had the sculpt the missing part of the arm and neck with MagicSculpt:

Finally, after checking the fit, it bothered me that the seatbelt straps were visible resting on the back of the seat. Obviously these straps should be going over the shoulders of the pilot. Since it would be a pain in the ass to make straps that would work seamlessly into the shoulders of the pilot and then drape over the back of the seat, I decided just to grind the offending straps off:

The above picture was in-progress. It came out smooth. Now that nobody will see the straps, I hope it won’t occur to them that the straps should be connected to the pilot.

Now I have to fit the tailwheel landing gear doors in place. I also have to decide if I want to cut out the doors on the Citroen. I can’t imagine if you were being buzzed by an enemy plane and scrambling away from your car for cover that you would bother to close the door behind you.

If I do cut out the doors, I then have to detail the interiors of the doors, since they are flat with no detail.

31 Days…

I don’t think I’ll make it…

I’ve been going back and forth this week on the cockpit of the Mustang and the Citroen car. There’s not a lot to show on the car since I’ve just desprued all the pieces and skewered them. The one thing I have done is cut out one of the doors, I’ve got to cut out the rear door later. I’m not really looking forward to it…

The last couple days I did a bit of masking to get ready for today. Sticky-tack is a real life-saver with all these small bits of detail:

I spent most of today painting the cockpit and pilot. I got quite a lot done for just one day through a mixture of airbrushing and hand-painting.

The Future gloss coat has been applied so as soon as it’s cured I can give it all a sludge wash and also dry-brush on some highlights, especially on the pilot. I’ve got to try to bring the details out on his face. The Mustang I’m building is from the African-American Tuskegee Airmen squadron. Unfortunately the skin-tone I mixed for the pilot isn’t much different from brown I mixed for the leather flight jacket and helmet. I’m also kind of bummed that the “Khaki” I painted the pants looked pea-green after it dried… Oh well, the pants will hardly show.

Anyway, a couple more hours of work should finish up the cockpit, then I can put the Mustang together, fix the seams and really get to work. I picked up a great set of 1/48 scale road signs which includes telephone poles, picket fence and even a funny little billboard. It should really liven up the dio.

Categories: Models In-Progress Tags:


March 2nd, 2009 No comments

Well, after destroying my own site by synching it with an empty folder (I thought the synch would work the other way…), it’s back! Thanks to Gamerabaenre for help getting it back.

A couple of the model gallery pages look funny after putting the site back together, there must be a couple files missing still, but before I get into tracking down small details like that I want to work out the big picture better.

In that vein, I’ve created a new header image to give my site a personal Funaka/mecha touch using an image of my Hazel Gigantic Arm Unit model. I may do more later, but it’s a start. I now have to redo my gallery pages in CSS so that they maintain a consistent theme, even if I make changes to it elsewhere.

Oh, and I have to post progress on my current WIP. Quite a bit of progress on the Mustang…

Categories: Generic Ramblings Tags: